Program Ports

Innovative solutions for your Panel Interface Connector (PIC) needs

We offer innovative solutions for your Panel Interface Connector (PIC) needs. Program Ports brand products are a comparable to: Automation Systems Interconnect (ASI), Daykin, GracePorts®, Hoffman, Mencom, McNaughton-McKay, Murr Elektronik, Qpic®, ZIPorts® and others.

Many of the innovative solutions have led to ports that offer:

  • S2EN which allows for selection between 2 EtherNets
  • S2RS which allows for selection between 2 RS232
  • S2ML which allows for selection between 2 MicroLogix
  • FI5HDT offers a female 15 pin High Density with Terminal connections using the smallest foot print in the market.

Are your program ports buried inside a locked enclosure? If so, bring it out!

Buried inside an enclosure, protected by a lock and disconnect, resides the PLC/CNC program port you need to make one quick change and get the line up and running again… Sound familiar? This line of program and interface ports attach directly to the program port of any CNC or PLC processor, allowing programmers safe access from outside of the enclosure. The ports can be customized to fit virtually ANY application, no matter the communications or power requirement, we can build it specifically for you!


Program Port Solutions


D (Duplex Outlet)

D (Duplex Outlet)

15 amp 110 volt

D (Duplex Outlet)


G (Ground fault interrupter)

G (Ground fault interrupter)

Ground fault interrupter
15 amp 110 volt

G (Ground fault interrupter)


S (Single Outlet)

S (Single Outlet)

Single Outlet
15 amp 110 volt

S (Single Outlet)


S (Single Outlet)

S (Single Outlet)

Single Outlet
15 amp 110 volt

S (Single Outlet)


M1 (Modular 1 gang)

M1 (Modular 1 gang)
  • Suitable for NEMA 4 & 12, where dust, oil mists, and wash downs are a concern
  • Modular construction with interchangeable components and covers
  • Plastic construction with Clear Cover
  • Requires less than 12 square inches of panel space
  • Can be ordered with 115/250v power
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

M1 (Modular 1 gang)


M2 (Modular 2 gang)

M2 (Modular 2 gang)
  • Suitable for NEMA 4 & 12, where dust, oil mists, and wash downs are a concern
  • Modular construction with interchangeable components and covers
  • Plastic construction with Clear Cover
  • Requires less than 21 square inches of panel space
  • Can be ordered with 115/250v power
  • Can be ordered with or without circuit breaker protection
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

M2 (Modular 2 gang)


M3 (Modular 3 gang)

M3 (Modular 3 gang)
  • Suitable for NEMA 4 & 12, where dust, oil mists, and wash downs are a concern
  • Modular construction with interchangeable components and covers
  • Plastic construction with Clear Cover
  • Requires less than 31 square inches of panel space
  • Can be ordered with 115/250v power
  • Can be ordered with or without circuit breaker protection
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

M3 (Modular 3 gang)


32 (size 32 pin housing)

32 (size 32 pin housing)
  • Suitable for NEMA 4, where wash downs are a concern
  • Metal cover construction
  • Requires less than 18 square inches of panel space
  • Can be ordered with or without 115V power
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

32 (size 32 pin housing)


24 (size 24 pin housing)

24 (size 24 pin housing)
  • Suitable for NEMA 4, where wash downs are a concern
  • Metal cover construction
  • Requires less than 14 square inches of panel space
  • Can be ordered with or without 115V power
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

24 (size 24 pin housing)


16 (Size 16 Pin Housing)

16 (Size 16 Pin Housing)
  • Suitable for NEMA 4, where wash downs are a concern
  • Metal cover construction
  • Requires less than 18 square inches of panel space
  • Can be ordered with or without 115V power
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

16 (size 16 pin housing)


10 (Size 10 Pin Housing)

10 (Size 10 Pin Housing)
  • Suitable for NEMA 4, where wash downs are a concern
  • Metal cover construction
  • Requires less than 10 square inches of panel space
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

10 (Size 10 Pin Housing)


6 (Size 6 Pin Housing)

6 (Size 6 Pin Housing)
  • Suitable for NEMA 4, where wash downs are a concern
  • Metal cover construction
  • Requires less than 18 square inches of panel space
  • Can be ordered with or without 115V power
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided

6 (Size 6 Pin Housing)


PC (Programming Center)

PC (Programming Center)
  • Suitable for NEMA 4, where wash downs are a concern
  • U.S. PAT#6,007,353
  • Polycarbonate construction
  • Requires less than 18 square inches of panel space
  • Can be ordered with or without 115V power
  • Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
  • All mounting hardware provided
  • Requires hand tool for opening cover

PC (Programming Center)


M2 (Modular 2 gang)

Special (Custom Products)

Since there are so many possible configurations that Program Parts can manufacture, please contact us and we’ll help you work through the particular requirements that you are in need of.

Special (Custom Products)







Looking for the rest of the pieces?

WECO engineers are trained to help you put the pieces together to form your infrared heating solution. WECO designs custom ovens for products as small as contact lenses and as big as swimming pools.
Contact us today to discuss your project with our engineers.