Power Options
Program Ports
Innovative solutions for your Panel Interface Connector (PIC) needs
Program Port Solutions
D (Duplex Outlet)
15 amp 110 volt
G (Ground fault interrupter)
Ground fault interrupter
15 amp 110 volt
S (Single Outlet)
Single Outlet
15 amp 110 volt
S (Single Outlet)
Single Outlet
15 amp 110 volt
M1 (Modular 1 gang)
- Suitable for NEMA 4 & 12, where dust, oil mists, and wash downs are a concern
- Modular construction with interchangeable components and covers
- Plastic construction with Clear Cover
- Requires less than 12 square inches of panel space
- Can be ordered with 115/250v power
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
M2 (Modular 2 gang)
- Suitable for NEMA 4 & 12, where dust, oil mists, and wash downs are a concern
- Modular construction with interchangeable components and covers
- Plastic construction with Clear Cover
- Requires less than 21 square inches of panel space
- Can be ordered with 115/250v power
- Can be ordered with or without circuit breaker protection
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
M3 (Modular 3 gang)
- Suitable for NEMA 4 & 12, where dust, oil mists, and wash downs are a concern
- Modular construction with interchangeable components and covers
- Plastic construction with Clear Cover
- Requires less than 31 square inches of panel space
- Can be ordered with 115/250v power
- Can be ordered with or without circuit breaker protection
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
32 (size 32 pin housing)
- Suitable for NEMA 4, where wash downs are a concern
- Metal cover construction
- Requires less than 18 square inches of panel space
- Can be ordered with or without 115V power
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
24 (size 24 pin housing)
- Suitable for NEMA 4, where wash downs are a concern
- Metal cover construction
- Requires less than 14 square inches of panel space
- Can be ordered with or without 115V power
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
16 (Size 16 Pin Housing)
- Suitable for NEMA 4, where wash downs are a concern
- Metal cover construction
- Requires less than 18 square inches of panel space
- Can be ordered with or without 115V power
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
10 (Size 10 Pin Housing)
- Suitable for NEMA 4, where wash downs are a concern
- Metal cover construction
- Requires less than 10 square inches of panel space
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
6 (Size 6 Pin Housing)
- Suitable for NEMA 4, where wash downs are a concern
- Metal cover construction
- Requires less than 18 square inches of panel space
- Can be ordered with or without 115V power
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
PC (Programming Center)
- Suitable for NEMA 4, where wash downs are a concern
- U.S. PAT#6,007,353
- Polycarbonate construction
- Requires less than 18 square inches of panel space
- Can be ordered with or without 115V power
- Attaches directly to the program port of most CNC or PLC processors, allowing programming access from outside of enclosure
- All mounting hardware provided
- Requires hand tool for opening cover
Special (Custom Products)
Since there are so many possible configurations that Program Parts can manufacture, please contact us and we’ll help you work through the particular requirements that you are in need of.
Looking for the rest of the pieces?
WECO engineers are trained to help you put the pieces together to form your infrared heating solution. WECO designs custom ovens for products as small as contact lenses and as big as swimming pools.
Contact us today to discuss your project with our engineers.
